Articles
Published articles, newest first. 22 in total · page 1 of 2
- Double-clad fibers and how pump light gets in: separate paths for laser light and pump lightWhy low-brightness diode pump light is hard to put straight into a thin core, and how a double-clad fiber solves it by giving the two kinds of light separate paths. Covers inner-cladding shapes, pumping from the end and the side, pump diodes, large-mode-area (LMA) fibers, and the limits that remain, from public sources.
- Limits of a single fiber (1): nonlinear effects (SBS, SRS)When strong light travels a long way through a thin core, the glass starts making new light. This article uses public sources to explain stimulated Brillouin scattering (SBS), where light bounces back off sound waves, and stimulated Raman scattering (SRS), where molecular vibrations shift light to longer wavelengths: how they work, how they differ, what sets their threshold, and how they are also put to use.
- Limits of a single fiber (2): heat and mode instabilityFiber lasers handle heat well, but the heat does not go away. This article uses public papers to explain how heat from the quantum defect and photodarkening changes the glass's refractive index, how that leads to transverse mode instability (TMI), where the beam suddenly starts to flicker above a certain average power, and what that 'threshold' means.
- How a fiber guides light: core and claddingWhy light inside a thin glass fiber does not leak out sideways: the refractive index difference between core and cladding, and total internal reflection. Also covers the numerical aperture (NA), single-mode and multimode fibers, and where these terms show up in articles on fiber lasers.
- ISR drones: why endurance mattersWhat intelligence, surveillance and reconnaissance (ISR) means, why staying aloft for a long time ties in with surveillance, the broad kinds of sensors drones carry, what changes when no one is on board, and public cases from Korea and NATO along with the debate over how drones are grouped, based on public sources.
- Q-switching and mode locking: two ways to make short pulsesQ-switching stores energy and releases it at once. Mode locking gets many waves in step. This article explains both ideas with diagrams and shows why different things set the pulse length and spacing in each.
- Why beam combining is needed, and its three approachesThere is a limit to how much power one fiber can deliver while keeping its beam quality. Using public review papers and textbooks, this article explains why beam combining, which brings the light of several lasers into one beam, came about; how light adds up with and without interference; how it differs from non-coherent combining; and what spectral beam combining and coherent beam combining each need to control and what they cost.
- Coherent beam combining: the principle, from published reviewsWhy does matching the phase bring several beams together into one? Using published review papers and textbooks, this article explains the principle of coherent beam combining through a two-port beam splitter and interference, the conditions of equal frequency, polarization, shape and timing, the active and passive ways to hold the phase, and the difficulties the reviews point out.
- Cold launch: why some missiles pop out before ignitingHow cold launch works, with the missile pushed out first and its motor lit only after it clears the launcher, which pushing forces public sources name, and public cases on submarines, ships and land-based silos, based on maker and museum descriptions.
- The US Army E-HEL laser contract and the directed-energy pilot at US basesThe US Army E-HEL high-energy laser contract as AeroVironment announced it, and the four systems that defense media say were named for a counter-drone directed-energy pilot at US bases, using only what has been made public.
- Radar: measuring distance and motion with radio wavesHow radar finds distance from the round-trip time of radio waves and motion from the Doppler effect, how it finds direction and height, how weather services and air traffic control use it, and where the name RADAR came from, based on public sources.
- Why fiber lasers became so widely used: from the lab to the factoryHow fiber lasers made it into factories: wall-plug efficiency, a shape that sheds heat, a beam that focuses to a small spot, and a design with few mirrors to align. A comparison with other industrial lasers and the limits that remain, from public sources.